2/6
Nr opisu: 0000035844 Autorzy: Md Irfan Ansari, Ajay Kumar, Danuta Grażyna Barnat-Hunek, Zbigniew Suchorab, Wojciech Andrzejuk, Dariusz Majerek. Tytuł pracy: Static and Dynamic Response of FG-CNT-Reinforced Rhombic Laminates Tytuł czasopisma: Szczegóły: 2018, Vol. 8, issue 5, article number 834 p-ISSN: 2076-3417 Charakterystyka formalna: artykuł w czasopiśmie zagranicznym Charakterystyka merytoryczna: artykuł oryginalny naukowy Charakterystyka wg MNiSW: artykuł w czasopiśmie z IF (wykaz MEiN) Język publikacji: ENG Wskaźnik Impact Factor ISI: 2.217 Punktacja ministerstwa: 25.000 Praca recenzowana Słowa kluczowe ang.: plates ; carbon nanotubes ; structure ; skew ; finite element method ; deflection ; frequency http://www.mdpi.com/2076-3417/8/5/834 DOI: 10.3390/app8050834 Streszczenie: The present study focuses on the static and dynamic response of functionally graded carbon nanotube (FG-CNT)-reinforced rhombic laminates. The cubic variation of thickness coordinate in the displacement field is considered in terms of Taylor's series expansion, which represents the higher-order transverse cross-sectional deformation modes. The condition of zero-transverse shear strain at upper and lower surface of FG-CNT-reinforced rhombic laminates is imposed in the present formulation. The present two-dimensional model is formulated in a finite element, with the C0 element consisting of seven nodal unknowns per node. The final material properties of FG-CNT-reinforced rhombic laminates are estimated using the rule of mixture. The obtained numerical are compared with the results available in the literature to verify the reliability of the present model. The present study investigates the effect of CNT distribution, loading pattern, volume fraction, and various combinations of boundary constraints by developing a finite element code in FORTRAN. Projekt/grant: : działalność statutowa WNET PSW, 2017-WNET/KNT/ZB/1
3/6
Nr opisu: 0000028190 Autorzy: Andrzej Zenon Raczkowski, Zbigniew Suchorab, Grzegorz Kucharczyk. Tytuł pracy: Modeling of air-flow in assembly hall supported by mechanical ventilation system Tytuł całości: W: Modern materials, installations and construction technologies / ed. by Stanisław Fic Miejsce wydania: Biała Podlaska Wydawca: Wydawnictwo PSW JPII Rok wydania: 2013 Strony zajęte przez pracę: S. 198-206 ISBN: 978-83-61044-39-0 Charakterystyka formalna: rozdział w monografii polskiej Charakterystyka wg MNiSW: rozdział w monografii - j. kongres. lub podst. dla dyscypliny Język publikacji: ENG Punktacja ministerstwa: 5.000 Liczba znaków: 23006 Liczba arkuszy: 0,57 Praca recenzowana Słowa kluczowe: wentylacja mechaniczna ; jakość powietrza ; obliczeniowa dynamika płynów Słowa kluczowe ang.: indoor air quality ; Computational fluid Dynamics Uwaga: sygn. 14757 XXVI CZYT. C ; 14758 XXVI CZYT. C [sprawdź dostępność w katalogu AB] Streszczenie: The aim this paper is to presents of simulations of mechanical ventilation system performance in assembly of the Faculty of Environmental Engineering, Lublin University of Technology. Simulation was conducted using Autodesk CFD Simulation 2013. 3D model of thre assembley hall was created in autodesk Revit Architecture application, which is directly connected to CFD Simulation program. There were conducted two variants of simulations: for winter conditions and for the summer performance. Obtained results enable to verify temperature values and air-flow velocities in the modeled room in each place and time. Conducted simulations showed that there are the areas with air parameters do not satisfying the design assumptions, required for thermal comfort and the correction of the applied solutions is needed. Air flow velocity distribution in the examined assembly hall, determining the indoor air parameters depends on many factors that were not considered in the described system solutions. The most important factor is temperature of the external barriers and the particular geometry of the room. Their consideration was only possible after creating the spatial model of the room and the ventilation system.
4/6
Nr opisu: 0000023063 Autorzy: Andrzej Zenon Raczkowski, Zbigniew Suchorab, Joanna Marczewska. Tytuł pracy: CFD simulations of mechanical ventilation behavior in commercial premises Tytuł całości: W: Energy-saving and ecological materials, installations and technology in construction / ed. by S. Fic Miejsce wydania: Biała Podlaska Wydawca: Wydawnictwo PSW JPII Rok wydania: 2012 Strony zajęte przez pracę: S. 92-98 ISBN: 978-83-61044-14-7 Charakterystyka formalna: rozdział w książce polskiej Język publikacji: ENG Praca recenzowana Słowa kluczowe: klimatyzacja ; obiekt usługowy ; program PyroSim
5/6
Nr opisu: 0000023062 Autorzy: Zbigniew Suchorab, Ewa Anna Zarzeka-Raczkowska. Tytuł pracy: Time Domain Reflectometry probes for measurement of in building materials. A review Tytuł całości: W: Energy-saving and ecological materials, installations and technology in construction / ed. by S. Fic Miejsce wydania: Biała Podlaska Wydawca: Wydawnictwo PSW JPII Rok wydania: 2012 Strony zajęte przez pracę: S. 76-91 ISBN: 978-83-61044-14-7 Charakterystyka formalna: rozdział w monografii polskiej Język publikacji: ENG Słowa kluczowe: pomiar wilgotności ; sonda powierzchniowa TDR ; technika reflektometryczna
6/6
Nr opisu: 0000028747 Autorzy: Zbigniew Suchorab, Agnieszka Żelazna, Grzegorz Łagód, Andrzej Zenon Raczkowski, Lucjan Pawłowski. Tytuł monografii: Komputerowe wspomaganie projektowania / Zbigniew Suchorab, Agnieszka Żelazna, Grzegorz Łagód, Andrzej Raczkowski; red. Lucjan Pawłowski Miejsce wydania: Lublin Wydawca: Komitet Inżynierii Środowiska PAN Rok wydania: 2010 Strony: 211 s., rys., 25 cm Seria: Monografie Komitetu Inżynierii Środowiska Polskiej Akademii Nauk ISBN: 978-83-89293-97-8 Kopia niedostępna: x Charakterystyka formalna: monografia polska (autor) Język publikacji: POL Słowa kluczowe: projektowanie ; projektowanie wspomagane komputerowo ; ogrzewanie płaszczyznowe ; ogrzewanie podłogowe Uwaga: Kopia niedostępna